Description

Periodically reads three orchestra control-signal values from an external file.

Syntax

kr1, kr2, kr3 readk3 ifilname, iformat, iprd

Initialization

ifilname -- an integer N denoting a file named "readk.N" or a character string (in double quotes, spaces permitted) denoting the external file name. For a string, it may either be a full path name with directory specified or a simple filename. In the later case, the file is sought first in the current directory, then in SSDIR, and finally in SFDIR.

iformat -- specifies the input data format:

Note that A-law and U-law formats are not available, and that all formats except the last two are binary. The input file should be a "raw", headerless data file.

iprd -- the rate (period) in seconds, rounded to the nearest orchestra control period, at which the signals are read from the input file. A value of 0 implies one control period (the enforced minimum), which will read new values at the orchestra control rate. Longer periods will cause the same values to repeat for more than one control period.

Performance

kr1, kr2, kr3 -- output of the signals read from ifilname.

This opcode allows three generated control signal values to be read from a named external file. The file should contain no header information but it should contain a regularly sampled time series of control values. For binary formats, the individual samples of each signal are interleaved. For ASCII text formats, the values are assumed to be separated by at least one whitespace character. The three "channels" in a sample frame may be on the same line or separated by newline characters, it does not matter. There may be any number of readk3 opcodes in an instrument or orchestra and they may read from the same or different files.

Examples

Here is an example of the readk3 opcode. It uses the file readk3.csd.

<CsoundSynthesizer>
<CsOptions>
; Select audio/midi flags here according to platform
-odac      ;;;realtime audio out
;-iadc    ;;;uncomment -iadc if realtime audio input is needed too
; For Non-realtime ouput leave only the line below:
; -o readk3.wav -W ;;; for file output any platform
</CsOptions>
<CsInstruments>

sr = 44100
ksmps = 32
nchnls = 2
0dbfs  = 1

giSine ftgen 0, 0, 2^10, 10, 1

instr 1 ;writes three control signals to a file
kfreq     randh     100, 1, 2, 1, 500 ;generates one random number between 400 and 600 per second
kdb       randh     12, 1, 2, 1, -12 ;amplitudes in dB between -24 and 0
kpan      randh     .5, 1, 2, 1, .5 ;panning between 0 and 1
          dumpk3    kfreq, kdb, kpan, "dumpk3.txt", 8, 1 ;writes the control signals
          prints    "WRITING:\n"
          printks   "kfreq = %f, kdb = %f, kpan = %f\n", 1, kfreq, kdb, kpan  ;prints them
endin

instr 2 ;reads the file written by instr 1
kf,kdb,kp readk3    "dumpk3.txt", 8, 1
          prints    "READING:\n"
          printks   "kfreq = %f, kdb = %f, kpan = %f\n", 1, kf, kdb, kp  ;prints again
kdb       lineto    kdb, .1 ;smoothing amp transition
kp        lineto    kp, .1 ;smoothing pan transition
aout      poscil    ampdb(kdb), kf, giSine
aL, aR    pan2      aout, kp
          outs      aL, aR
endin

</CsInstruments>
<CsScore>
i 1 0 5
i 2 5 5
e
</CsScore>
</CsoundSynthesizer>

The output should include lines like these:

WRITING:
kfreq = 473.352855, kdb = -15.197657, kpan = 0.366764
kfreq = 473.352855, kdb = -15.197657, kpan = 0.366764
kfreq = 441.426368, kdb = -19.026206, kpan = 0.207327
kfreq = 452.965140, kdb = -21.447486, kpan = 0.553270
kfreq = 585.106328, kdb = -11.903852, kpan = 0.815665
kfreq = 482.056760, kdb = -4.046744, kpan = 0.876537

READING:
kfreq = 473.352900, kdb = -15.197700, kpan = 0.366800
kfreq = 473.352900, kdb = -15.197700, kpan = 0.366800
kfreq = 441.426400, kdb = -19.026200, kpan = 0.207300
kfreq = 452.965100, kdb = -21.447500, kpan = 0.553300
kfreq = 585.106300, kdb = -11.903900, kpan = 0.815700
kfreq = 482.056800, kdb = -4.046700, kpan = 0.876500
      

See Also

dumpk, dumpk2, dumpk3, dumpk4, readk, readk2, readk4

Credits

By: John ffitch and Barry Vercoe

1999 or earlier